Contact us at 248-650-0603
The Bushings Inc. Vibro-Leveler is a dual purpose, rubber-in-shear machine mount that suppresses the transmission of vibration and noise, and allows precision leveling of your machines.
Vibro-Leveler Mounts Benifits:
Nine shelf-standard sizes can meet your specific requirements. Available in capacities from 10 to 1,000 pounds, Vibro-levelers provide an ample safety margin. Even when overloaded to destruction, they only permit a drop of less than one-half inch.
Bushings, Inc. recommends Vibro-Levelers both for new and existing machines. Typical applications include printing equipment, enclosure systems, blowers, compressors, punch presses, vacuum pumps, hydraulic presses, jig borers, screw machines, snag grinders, offset press systems, and testing equipment.
Download Printable Vibro-Leveler Machine Mounts Selection Table
Usually, Vibro-Leveler are installed under a machine. Simply raise or tilt the machine to allow a “Vibro-Leveler” to be slipped under the base. Insert its stud into the hold-down bolthole in the base of the machine. To level the machine, adjust the lower nut upwards to hold the machine on an even plane, then lock the upper nut down to hold the machine in position. The Vibro-Levelers come complete including the leveling and locking nuts; no fitting, cutting, or threading of any kind is required. Where the machine must be kept at or near its original level, brackets are either bolted or welded to the side of the base. Ordinary structural brackets are ideal for this. Though seldom required, hold down boltholes in the base of each mount permits securing to the floor.
While a typical installation requires four Vibro-Levelers, any number may be used to accommodate machinery requiring more (or fewer) points of suspension. Once the total weight of the machine is established, refer to the accompanying specification table to determine the correct mounting number(s) based on their weight bearing capacities. The combined capacity of the number of mountings should equal or exceed the total weight of the machine to be supported. For example, if the machine weighs a total of 700 lbs. and mounts are to be positioned in a four point suspension pattern, each point supports 175 lbs., and four 200 lb. Vibro-Levelers (mounting number 3200) should be used.
If the machine to be supported is not symmetrical so that there would be considerably more weight on one end than the other, the mountings on the heavier end must be of correspondingly greater capacity.
| A | B | C | D | E | F | G | H | I | J | ||||
| Mount Number | Load Capacity of Each Mounting (lbs) | Shipping Weight Each | Average Deflection Under Rated Load | Height Floor To Top of Nut Min. Ht Above Floor | Height (O.A) Mount Inc’l Stud | Height of Stud Above Lower Nut | ∅ Stud | ∅ Housing | Bolt Hole Centers | ∅ Base | Flange Height | ∅ Bolt Holes in Base | Height of Body Above Flange |
| 3010 | 10 | 5 oz. | 0.0625″ | 1 1/8″ | 2 1/8″ | 1″ | 5/16″ | 1 1/4″ | 1 7/8″ | 2 1/2″ | 11/64″ | 1/4″ | 9/16″ |
| 3025 | 25 | 7 oz. | 0.0625″ | 1 5/8″ | 2 3/4″ | 1″ | 3/8″ | 1 1/4″ | 1 7/8″ | 2 1/2″ | 11/64″ | 1/4″ | 1″ |
| 3050 | 50 | 7 oz. | 0.0625″ | 1 5/8″ | 2 3/4″ | 1″ | 3/8″ | 1 1/4″ | 1 7/8″ | 2 1/2″ | 11/64″ | 1/4″ | 1″ |
| 3100 | 100 | 10 oz. | 0.0625″ | 1 3/4″ | 3″ | 1 1/8″ | 3/8″ | 1 1/2″ | 2 7/16″ | 3″ | 11/64″ | 5/16″ | 1 1/8″ |
| 3200 | 200 | 1lb 6 oz. | 0.0625″ | 2 1/4″ | 3 3/4″ | 1 3/8″ | 1/2″ | 1 7/8″ | 2 3/4″ | 3 1/2″ | 3/16″ | 3/8″ | 1 1/2″ |
| 3300 | 300 | 1lb 14 oz. | 0.0625″ | 2 3/4″ | 4 3/4″ | 2″ | 1/2″ | 2″ | 3″ | 4″ | 3/16″ | 3/8″ | 2″ |
| 3500 | 500 | 1lb 10 oz. | 0.0625″ | 3 1/2″ | 6″ | 2 1/2″ | 1/2″ | 2 1/8″ | 3 1/2″ | 4 1/2″ | 3/16″ | 3/8″ | 2 3/4″ |
| 3750 | 750 | 9lbs | 0.0625″ | 5″ | 8 5/8″ | 4″ | 1″ | 4 1/2″ | 6 1/2″ | 7 3/4″ | 3/8″ | 5/8″ | 3″ |
| 4000 | 1000 | 9lbs | 0.0625″ | 5″ | 8 5/8″ | 4″ | 1″ | 4 1/2″ | 6 1/2″ | 7 3/4″ | 3/8″ | 5/8″ | 3″ |
For additional application assistance, contact us at the factory by phone 248-650-0603, fax 248-650-0606 or by e-mail.